New drugstore cialis australia online viagradirect.net with a lot of generic and brand drugs with mean price and fast delivery.
X-shield epoxylock epn.pub
Technical Data Sheet
X-Shield EpoxyLock EPN
High performance epoxy novolac coating for concrete and steel
X-Shield EpoxyLock EPN is a high performance, high build
epoxy novolac protective coating suitable for use in a wide
range of applications including those requiring extremely
• Can be applied to steel and concrete
• Protection of concrete and steel structures from
• Wall and floor coating for industrial facilities
X-Shield EpoxyLock EPN is not suitable for use with the
Dry film thickness
Chemicals at greater concentrations than shown above
Ethylene glycol momoethyl ether Formic acid
Volatile Organic Content
X-Shield EpoxyLock EPN is suitable for use in contact with
the following chemicals discoloration of the coating may
4m² per liter (158ft2 per gallon) per coat.
Actual coverage will depend on wastage and surface
profile and can be up to 20% higher than theoretical
18 months when stored below 35C (95F) under shade in
X-Shield EpoxyLock EPN is resistant to ultra violet
radiation from direct sunlight and will maintain its
chemical and physical properties. As is typical with all
epoxy coatings, the color will change slightly on
X-Shield EpoxyLock EPN should be applied by
experienced coating crews. X-Calibur provides detailed
method statements on all its products for use in various
applications. These must be referred to prior to starting
work. The information below is a summary intended for
Apply only on to slabs that have a waterproofing system
The substrate must be structurally sound. Loose or
installed in order to prevent blistering due to osmosis.
unsound concrete should be removed and made good.
Surfaces must be entirely free of oil, grease, paint,
Health and Safety
corrosion deposits, dust, laitance or other surface
This product is for industrial use only by trained
deposits. The surface should be prepared by light grit
operatives. It is potentially hazardous if not used
blasting or high pressure water blasting to produce a
correctly. Please refer to the Material Safety Data
lightly exposed aggregate surface. The use of a primer is
Sheet (MSDS) prior to the purchase and use of
not normally required on good quality well prepared
this product. The MSDS can be obtained via our
substrates. However if the substrate is very porous or
subject to high loads then the surface should be primed
with X-Shield SF Primer. If the substrate has a relative
Authorized Technical Specialist
humidity >75% then prime using X-Shield MT Primer.
Please note that only X-Calibur Authorized Technical
Any bug holes should be filled with an X-Shield BugFill.
Specialists (‘ATSs’) are permitted to change any of the
information in this data sheet or to provide written
recommendations concerning the use of this product.
Surfaces should be thoroughly cleaned and degreased to
Visit www.x-calibur.net for a full list of X-Calibur ATSs.
SSPC-SP1 prior to blasting. All sharp edges, protuber-
ances, welds, etc should be ground down to remove any
sharp edges. The degreased surface should now be grit
X-Calibur makes modifications to its product datasheets
blasted to a minimum SA 2½ in accordance with BS7079
on a continuous basis. Please check the datasheet
Part A1 or equivalent. This means very thorough blast
update section on www.x-calibur.net to ensure you have
cleaning using chilled steel grit to provide near white
metal 85% clean. The surface shall be free from all
foreign matter. A surface profile of 45 microns is the
recommended finish. All dust and abrasive residue must
X-Calibur supplies products that comply with the
be removed from the surface prior to application of the
properties shown on the current datasheets. In the
first coat. Depending on the level of corrosion protection
unlikely event that products supplied are proved not to
required, an anti-corrosion or holding primer may be
comply with these properties, then we will replace the
non-compliant product or refund the purchase price.
X-Calibur does not warrant or guarantee the installation
of the products as it does not have control over the
Add the hardener ‘Part B’ into the base ‘Part A’ and mix
installation or end use of the products. Any suspected
using a slow speed drill (500 rpm) with an X-Shield
defects must be reported to X-Calibur in writing within
Coating Mixer Paddle for 3 minutes or until both
five working days of being detected. X-Calibur
components have fully dispersed and are uniform in
Construction Systems Inc. makes no warranty as to
color. Be sure to rotate the mixer throughout the drum.
merchantability or fitness for a particular purpose
and this warranty is in lieu of all other warranties
express or implied.
X-Calibur Construction Systems
Inc. shall not be liable for damages of any sort including
Apply in two coats of 250 micron (10.5mils) wet film
remote or consequential damages, down time, or delay.
thickness using brush or roller. The first coat should be
applied in such a manner as to ensure a good bond.
X-Calibur Construction Systems Inc.
Allow first coat to dry for at least 8 hours at 20C (68F) or
4 hours at 35C (95F). For application by airless spray
consult X-Calibur before use. Clean equipment using
(954) 885 9912 F
(954) 885 9913
G6PD Deficiency capable of producing the G6PD enzyme, resulting is an important element (enzyme) in the glucose in more severe symptoms. Females, on the other oxidation (oxygen utilization) process of red blood hand, inherit two X chromosomes, one from each cells (RBCs) and for maintaining their normal life parent. A mutation in one copy is compensated for span. G6PD deficiency is an inh
Implantation subfascial de la pompe intratecal à Baclofène aux enfants spastiques. Auteurs: G. de Coulon, C. Dimitri, V. de Rosa, A. Kaelin. Hôpital Universitaire de Genève Abstract : La pompe à Baclofen intratecal devienne de plus en plus valable comme la méthode pour contrôler la spasticité et la dystonie dans les enfants atteints de lésion cérébrale grave. Ce traitemen